(1)檢查并清洗粗油濾清器，更換濾芯。
(1) Check and clean the crude oil filter and replace the filter element.
(2)拆卸油精過濾器。
(2) Remove oil filter.
檢查并清洗油底殼，設置濾清器，檢查曲軸軸承緊固度，擰緊曲軸軸承螺栓、螺母。
Check and clean the oil pan, set filter, check the tightness of crankshaft bearing, tighten the bolts and nuts of crankshaft bearing.
(4)熱車釋放臟油，加入清洗劑，清洗發動機油路。
(4) Hot car releases dirty oil, adds cleaning agent, and cleans engine oil path.
5. 檢查并清潔汽油過濾器。
5. Check and clean the gasoline filter.
檢查汽油泵和管路。
Check the petrol pump and pipeline.
7 .清洗火花塞碳，糾正電極間隙，檢查是否有漏油現象。
7. Clean spark plug carbon, correct electrode gap and check for oil leakage.
今天清洗、檢查、調整分配器。
Clean, check and adjust the distributor today.
檢查和調整閥門間隙。
Check and adjust valve clearance.
負責進排氣歧管的緊固。
Be responsible for tightening intake manifold and exhaust manifold.
清洗發動機空氣過濾器和曲軸箱通風空氣過濾器。
Clean engine air filter and crankcase ventilation air filter.
清潔曲軸箱通風單向閥和管道。
Clean crankcase ventilation one-way valves and pipes.
擰緊泵的螺栓、螺母，調整風機v形皮帶的松緊。
Tighten the bolts and nuts of the pump and adjust the tightening of the V-belt of the fan.
按下列順序和力矩?cái)Q緊氣缸蓋螺栓。
Tighten cylinder head bolts in the following order and moment.
清洗化油器進口過濾器，清洗化油器殼體，檢查聯動機構，擰緊連接螺栓。
Clean the carburetor inlet filter, clean the carburetor shell, check the linkage mechanism and tighten the connecting bolt.
參與發動機支架的連接及損壞情況。
Participate in the connection and damage of engine bracket.
負責，擰緊，調整散熱器。
Responsible for tightening and adjusting the radiator.
注意，擰緊油箱和油管。
Attention, tighten tank and tubing.
負責，緊固排氣歧管和消聲器。
Responsible for tightening exhaust manifold and muffler.
監測發動機的燃燒效果，并進行調整。
Monitor the combustion effect of the engine and adjust it.
(2)二級底盤維護
(2) Maintenance of secondary chassis
(1)檢查離合器盤和分離軸承;檢查分離桿，調整分離軸承與分離桿之間的間隙;調整離合器踏板自由行程;次潤滑傳動軸前軸承和分離軸承。
(1) Check the clutch disc and separating bearing; check the separating rod, adjust the clearance between the separating bearing and the separating rod; adjust the free travel of the clutch pedal; lubricate the front bearing and the separating bearing of the transmission shaft for the first time.
(2)檢查轉向節襯套與主銷配合是否緊固;擰緊主銷水平銷螺栓。
(2) Check whether the steering knuckle bushing is tightened with the main pin; tighten the horizontal pin bolt of the main pin.
Jinan Mercedes-Benz automobile repair which good to look for Jinan Lutong automobile repair repair, more knowledge about automobile repair click on the official website for consultation: http://www.cnjqf.com/
