在高端汽車領域，奔馳以精密工程與卓越性能著稱，其保養維護需建立科學化、精細化的養護體系。從機械系統到電子模塊，從常規保養到深度養護，車主需掌握六大核心維度，確保車輛始終處于最佳狀態。

　　In the high-end automotive field, Mercedes Benz is known for its precision engineering and excellent performance, and its maintenance requires the establishment of a scientific and refined maintenance system. From mechanical systems to electronic modules, from routine maintenance to deep maintenance, car owners need to master six core dimensions to ensure that their vehicles are always in optimal condition.

　　一、養護周期的精準把控

　　1、 Accurate control of maintenance cycle

　　奔馳官方保養手冊將保養周期分為A保、B保兩大類：

　　The official maintenance manual of Mercedes Benz divides the maintenance cycle into two categories: A maintenance and B maintenance:

　　A保（基礎保養）

　　A Guarantee (Basic Maintenance)

　　每行駛1萬公里或12個月進行，核心項目包括機油機濾更換、全車油液檢查、輪胎氣壓校正等。采用低粘度全合成機油，可提升燃油經濟性3%-5%。

　　Every 10000 kilometers or 12 months of driving, the core projects include oil filter replacement, full vehicle oil inspection, tire pressure correction, etc. Using low viscosity fully synthetic engine oil can improve fuel economy by 3% -5%.

　　B保（深度保養）

　　B Guarantee (Deep Maintenance)

　　每行駛2萬公里或24個月實施，涵蓋空氣濾清器、空調濾清器、剎車油、火花塞等18項檢測更換。在渦輪增壓車型中，需額外進行中冷器清潔與增壓管路檢查。

　　Implemented every 20000 kilometers or 24 months, covering 18 tests and replacements such as air filters, air conditioning filters, brake oil, spark plugs, etc. In turbocharged models, additional cleaning of the intercooler and inspection of the boost pipeline are required.

　　二、關鍵系統的專項養護

　　2、 Special maintenance of critical systems

　　對核心部件實施預防性維護，可延長使用壽命：

　　Implementing preventive maintenance on core components can extend their service life:

　　動力總成養護

　　Powertrain maintenance

　　采用縱置布局的發動機，需每3萬公里進行缸內積碳清洗。使用核桃砂物理清洗技術，避免化學清洗劑對氧傳感器的腐蝕，恢復發動機壓縮比至設計值±2%。

　　An engine with a vertical layout requires carbon cleaning of the cylinder every 30000 kilometers. Use walnut sand physical cleaning technology to avoid corrosion of the oxygen sensor by chemical cleaning agents and restore the engine compression ratio to the design value ± 2%.

　　傳動系統維護

　　Transmission system maintenance

　　9速自動變速箱需每6萬公里更換專用油液，采用等量交換法，確保油液填充量精確至±0.2L。對四驅車型，需檢查分動箱油位與傳動軸防塵套完整性。

　　The 9-speed automatic transmission requires the replacement of specialized oil every 60000 kilometers, using an equal amount exchange method to ensure accurate oil filling to ± 0.2L. For four-wheel drive models, it is necessary to check the transfer case oil level and the integrity of the transmission shaft dust cover.

　　底盤系統調校

　　Chassis system calibration

　　每行駛4萬公里進行四輪定位參數校準，重點調整前束角與外傾角。對配備空氣懸架的車型，需使用專用診斷儀進行高度傳感器校準，誤差控制在±1mm以內。

　　Perform four-wheel alignment parameter calibration every 40000 kilometers, with a focus on adjusting the toe angle and camber angle. For vehicles equipped with air suspension, a dedicated diagnostic instrument is required for height sensor calibration, with an error controlled within ± 1mm.

　　三、電子系統的深度檢測

　　3、 Deep detection of electronic systems

　　現代奔馳車型搭載30余個電子控制單元，需定期進行軟件更新與硬件檢測：

　　Modern Mercedes Benz models are equipped with over 30 electronic control units, which require regular software updates and hardware testing

　　診斷儀全掃描

　　Diagnostic instrument full scan

　　使用奔馳原廠診斷儀STAR D，對CAN總線、LIN總線、MOST總線進行通信質量檢測。重點監控發動機控制模塊、變速箱控制模塊、車身控制模塊的故障碼存儲情況。

　　Use the Mercedes Benz original diagnostic tool STAR D to perform communication quality checks on the CAN bus, LIN bus, and MOST bus. Focus on monitoring the fault code storage status of the engine control module, transmission control module, and body control module.

　　軟件版本管理

　　Software version management

　　每12個月進行控制單元軟件升級，優化發動機標定、變速箱換擋邏輯、能量回收策略等參數。實測顯示，軟件升級可使綜合油耗降低2%-4%。

　　Upgrade the control unit software every 12 months to optimize parameters such as engine calibration, transmission shift logic, and energy recovery strategy. Tests have shown that software upgrades can reduce overall fuel consumption by 2% -4%.

　　傳感器校準

　　Sensor calibration

　　對毫米波雷達、攝像頭、超聲波傳感器等22類傳感器進行動態校準。在自適應巡航系統中，需確保雷達波束角度偏差<0.5°，保障駕駛輔助系統的可靠性。

　　Dynamically calibrate 22 types of sensors, including millimeter wave radar, cameras, and ultrasonic sensors. In the adaptive cruise control system, it is necessary to ensure that the radar beam angle deviation is less than 0.5 ° to ensure the reliability of the driving assistance system.

　　四、易損件的預防性更換

　　4、 Preventive replacement of vulnerable parts

　　建立易損件壽命數據庫，實施精準更換：

　　Establish a database for the lifespan of vulnerable parts and implement precise replacement:

　　制動系統

　　brake system

　　剎車片摩擦材料厚度<3mm時需更換，采用低金屬配方剎車片，可減少粉塵排放40%。對配備陶瓷剎車盤的車型，需使用專用工具進行盤面平整度檢測。

　　When the thickness of the brake pad friction material is less than 3mm, it needs to be replaced. Using low metal formula brake pads can reduce dust emissions by 40%. For models equipped with ceramic brake discs, special tools are required to perform flatness testing on the disc surface.

　　輪胎管理

　　Tire management

　　采用胎壓監測系統（TPMS），實時監控輪胎壓力與溫度。當胎紋深度<3mm時，需更換為原廠認證輪胎，確保濕地抓地力符合歐盟ECE R117標準。

　　Adopting tire pressure monitoring system (TPMS) to monitor tire pressure and temperature in real-time. When the tread depth is less than 3mm, it is necessary to replace it with original factory certified tires to ensure that the wet grip meets the EU ECE R117 standard.

　　濾清器系統

　　Filter system

　　空氣濾清器每2萬公里更換，采用HEPA級濾材，對PM2.5過濾效率達99.5%。空調濾清器每1萬公里更換，附加活性炭層，可吸附90%以上的有害氣體。

　　The air filter is replaced every 20000 kilometers and uses HEPA grade filter material, with a filtration efficiency of 99.5% for PM2.5. The air conditioning filter is replaced every 10000 kilometers with an additional activated carbon layer that can adsorb over 90% of harmful gases.

　　五、特殊工況的應對策略

　　5、 Response strategies for special working conditions

　　針對不同使用場景，制定專項養護方案：

　　Develop specialized maintenance plans for different usage scenarios:

　　高溫環境養護

　　High temperature environment maintenance

　　在環境溫度>35℃時，需加強冷卻系統檢測。每2萬公里更換冷卻液，確保冰點<-35℃，沸點>135℃，防止發動機開鍋。

　　When the ambient temperature is above 35 ℃, it is necessary to strengthen the detection of the cooling system. Replace the coolant every 20000 kilometers to ensure that the freezing point is below -35 ℃ and the boiling point is above 135 ℃, in order to prevent the engine from boiling.

　　低溫環境啟動

　　Low temperature environment startup

　　在環境溫度<5℃時，需使用電加熱機油濾清器，預熱機油至40℃以上再啟動，降低冷啟動磨損60%。對柴油車型，需安裝進氣預熱格柵。

　　When the ambient temperature is below 5 ℃, an electrically heated oil filter should be used to preheat the oil to above 40 ℃ before starting, reducing cold start wear by 60%. For diesel models, it is necessary to install an intake preheating grille.

　　涉水行駛處理

　　Handling of driving through water

　　通過積水路段后，需立即檢查空氣濾清器濕度。如發現進水，需更換濾清器并對發動機艙進行干燥處理，防止電子模塊腐蝕。

　　After passing through the flooded section, it is necessary to immediately check the humidity of the air filter. If water is found to have entered, the filter should be replaced and the engine compartment should be dried to prevent corrosion of the electronic module.

　　六、養護質量的溯源管理

　　6、 Traceability management of maintenance quality

　　建立數字化養護檔案，實現全生命周期追溯：

　　Establish digital maintenance records to achieve full lifecycle traceability:

　　電子健康檔案

　　Electronic health records

　　通過Mercedes me APP，可查看歷史保養記錄、維修診斷報告、零件溯源信息。對更換的每個零件，可掃描二維碼查詢生產批次與質檢報告。

　　Through the Mercedes me app, users can view historical maintenance records, repair diagnostic reports, and parts traceability information. For each replaced part, the production batch and quality inspection report can be queried by scanning the QR code.

　　養護過程監控

　　Monitoring of maintenance process

　　在授權服務中心，關鍵保養工序需通過視頻記錄存檔。如機油加注量、螺栓緊固扭矩等參數，可隨時調取復查。

　　At the authorized service center, critical maintenance procedures need to be recorded and archived through video. Parameters such as oil filling amount and bolt tightening torque can be retrieved and rechecked at any time.

　　質量反饋機制

　　Quality feedback mechanism

　　保養后72小時內，客服中心進行滿意度回訪。如發現養護質量問題，啟動快速響應流程，48小時內完成整改并復檢。

　　Within 72 hours after maintenance, the customer service center will conduct a satisfaction follow-up. If any maintenance quality issues are found, initiate a rapid response process, complete rectification and re inspection within 48 hours.

　　本文由濟南奔馳汽車保養友情奉獻.更多有關的知識請點擊:http://www.cnjqf.com我們將會對您提出的疑問進行詳細的解答，歡迎您登錄網站留言.

　　This article is a friendly contribution from Volvo Car Repair in Jinan For more information, please click: http://www.cnjqf.com We will provide detailed answers to your questions. You are welcome to log in to our website and leave a message